MECHMANTRA- 2024

Description:

Design a wired/wireless manually controlled robot which should be able to travel on land, sand, and water etc. The robot that traverses all the hurdles and completes the track in the minimum amount of time is declared as the 'DEATH RACE WINNER'.

Bot Specifications:

The dimensions of the vehicle must be within (40x40x40) cm. The robot can be wired/ wireless. In case of wired control, the wires should be slack all the time. In case of wireless control, the RC should have two remote control circuits (or dual frequency remote control circuit/Bluetooth) which can be switched to either of the frequency before the event. The power supply for the vehicle should not exceed 12V DC between any two points in the circuit at any given time. Use of readymade chassis/ RC Car is not allowed. Use of IC engine or compressor is not allowed. All the robots must depend only on motors for their propulsion and control. The body of the vehicle must be covered, to avoid any entanglement between two competing robots. Damaging the wires of opponent will lead to disqualification.

Arena Specifications:

The robot has to traverse through a rough terrain of width 0.5 to 1m which is surrounded by a barrier of height 20cm.
The arena has 6 types of regions:

• Region 1: The robot has to move across a series of speed breakers, each of radius 2.5cm.
• Region 2: The robot has to move through a pit of depth 10cm.
• Region 3: A small portion of the track is filled with sand (with depth 3cm) on which the robot has to traverse.
• Region 4: The track is elevated with an inclination of 30 degrees in this part.
• Region 5: This region is a graveled path.
• Region 6: In this region, the robot has to travel through a damp area, filled with water with a depth of 3cm.
• Note: Some other regions which are not specified here will be present.

Rules:

• Teams must start their Robots from the starting line only after a signal is given by the Referee. The timer starts immediately after the signal is given.
• Number of participants per team should not exceed 5. Bot should always remain inside the track.
• If the bot leaves the track at any point during the race or becomes immobile, it will be considered as a “PIT FALL,” which is an opportunity to repair or relocate the bot. Each pit fall spans for 1 minute. The first three pit falls are considered to be penalty-free.
• Only two persons from a team are allowed to manipulate the bot during a pit fall. One hour before the event, the bot must go through a specification check. Misbehavior of a participant will lead to disqualification or a reduction in points.
• If special circumstances, such as unforeseen problems or capabilities of a robot, occur, rules may be modified by the referee. The referee's decision will be final.
• Use of any unfair practices during the competition will result in disqualification from the arena.

Judging Criteria:

The time taken to complete the whole track is solely considered. The robot which completes the track in least time is declared as the winner. Wireless controlled robots will have some advantage in the track. In case of a tie then other factors such as no of pitfalls are considered. There will be a penalty of Time if the Robot is not able to move on a particular hurdle, it can be skipped.

Staff Co-ordinators

Students Co-ordinators

Description:

Here is an amazing opportunity to showcase your ideas on a unique and massive platform in the form of well integrated and intriguing presentation. It strives to explore the inquisitiveness of young minds by giving their incredulous ideas a definitive direction.

RULES AND REGULATIONS:

• The paper should strictly follow standard IEEE two-column format (The format can be downloaded from the internet). The paper should be in PDF format, readable in Adobe Acrobat Reader.
• A team should consist of a maximum of 3 members. Paper should contain a maximum of 10 pages. Presentation should be less than 7 minutes.
• Qualified candidates are required to bring along with them 1 soft copy (preferably in a pen drive) and 2 hard copies of the technical paper on the day of the event.
• The decision of the judges and event head shall be treated as final and binding on all. The topics are based on the mechanical stream.

Staff Co-ordinators

Students Co-ordinators

Description:

Round 1: A Written test is conducted on the basics of AUTOCAD Software.
Round 2: 2-D drawings should be drawn using AUTOCAD Software.

Rules :

1. Prizes will be awarded on the basis of time taken for designing
2. The decision of the judges and event head shall be treated as final and binding on all.

Staff Co-ordinators

Students Co-ordinators

Description:

Working Model of any type can be submitted and should be clearly described by the participants.

Rules and Regulations:

• Model must have at least one moving part; stationary models are not considered.
• Prizes will be awarded on the basis of the objective of the model and its application in day-to-day life.
• The team size is restricted to a maximum of five individuals.
• A maximum of two persons are allowed to explain the working model.
• The decision of the judges and event head shall be treated as final and binding on all.

Staff Co-ordinators

Students Co-ordinators

THE PORTRAYAL

It consists of four rounds:

Staff Co-ordinators

Students Co-ordinators